BANDLUXE R300 MANUAL PDF
July 29, 2020 | by admin
This manual contains instructions for installing and configuring the product. Read the manual carefully before you use the product, so that you can fully exploit. Thank you for your purchase of the PR Series HSPA+ WLAN Pocket. Router. This device is designed to access the Internet via G technology and share. User Manual. Zain Router R HSPA+ / HSPA Router. P/N: Rev. A. Table of Contents BandLuxe R User Manual Uploaded by.
|Published (Last):||10 December 2015|
|PDF File Size:||13.24 Mb|
|ePub File Size:||14.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Bandluxe R300 Login Instructions
Documents Flashcards Grammar checker. Important Safety Information and Glossary. This product is designed to access the Internet via 3. It is easy to configure and operate even for non-technical users. This manual contains instructions for installing and configuring the product.
Read the manual carefully before you use the product, so that you can fully exploit the product functions. To bandluxxe the Router’s factory settings, press the reset button for longer than 5 sec.
Flashing light shows that data is being transmitted via WLAN. Flashing light shows that data is being transmitted via LAN.
Connect the power adaptor to the Router and connect it to an outlet. Turn on the Power switch. One of the following two methods can be chosen to link your Router with PC. To link the Router with your PC via Ethernet cable, connect one end of the cable to the LAN port on the Router, and the other end of the cable to the Ethernet port on your computer. The Router uses a web-based configuration utility.
To access the configuration utility, open a browser for example Internet Explorer and enter the IP address http: Enter the Router User name admin and Password hsparouter. Select the connection type you prefer. Roaming Connection To allow roaming network connection, select Enabled. To block roaming connection, select Disabled. Charges for roaming connection may be high.
Contact your mobile network operator for more information. You can choose to set the APN automatically or manually. You can set the idle time for the 3. When the Router is idle, the connection will be disconnected automatically after the idle time expires. The connection is always kept on.
Bandrich – R300
This option is commonly used baandluxe cable modem services. Your ISP will provide you with a username and password. This option is typically used for DSL services. Enter a maximum idle time during which the Internet connection is maintained during inactivity. If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router automatically tries to re-establish your connection.
To use this option, select Keep Alive. In the Redial Period field, specify how often you want the Router to check the Internet connection. Enter the IP address Subnet Mask: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, the Router automatically tries to re-establish your connection. In the Redial Period field, f300 specify how often you want the Router to check banrluxe Internet connection.
It allows an Internet domain name to be assigned to a computer with a varying dynamic IP address. From the drop-down list, select your DDNS service type. Enter the user name for your DDNS banlduxe. Enter the password for your DDNS account.
All aliases for your domain such as www. This allows users to access your computer using all types of derivatives of your domain name. Because it is dynamic, it changes.
This shows whether the DDNS service is enabled or disabled. Some ISPs require these names as identification. In most cases, leaving the fields blank will work.
Automatically adjust clock for daylight saving changes: Select the checkbox to enable Daylight Saving time. The default IP address is Keeping the default values will work. A list of DHCP clients is displayed with the following information: To add clients, click Add Clients.
If you want to remove a client from this list, click Remove. To view the most up-to-date information, click Refresh. Maximum Number of Users: The length of time for the IP address lease.
Enter the lease time in minutes. The Router will use these for quicker access to functioning DNS servers. Otherwise, leave this blank. RIP The Routing Information Protocol RIP helps the Router dynamically adapt to changes of network connections by communicating information about which networks each Router can reach and how far away those networks are.
Static Routing This section allows you to define fixed routes to defined destinations. To set up a static route, select a number from the drop-down list. Enter a name for the route here. Enter the Destination IP address that will be assigned to a specific network or host. Enter the subnet mask associated with the Destination IP. This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.
Click Show Routing Table to open a screen displaying how data is routed through your local network. Click Refresh to update the information. They usually provide connectivity to various devices behind a gateway or firewall. Since it is mainly a Layer 3 technology, it can secure all data on the network. From this drop-down menu, you can select the wireless standards running on your network. If you have If you have only If you do not want to use any WiFi network, select Disabled. The radio channel number.
The permissible channels depend on the Regulatory Domain. Disable this function will let your SSID setting not be exposed to view in the air.
Routersetup – Bandrich :: R
This will prevent computers scanning for the presence of wireless networks to detect your network name. Select a level in the Security Mode drop-down menu. Select a standard from kanual drop-down list.
The bits encryption requires 10 hexadecimal digits letters a-f and numbers are valid. The bits encryption requires 26 hexadecimal digits letters a-f and numbers are valid. You can set up to four different keys. Strings of hexadecimal characters are not easy to remember. This conversion utility converts a simple word or phrase into hex, so that you can easily remember and regenerate the pass-phrase.
You can specify which key you want to use for the WiFi network.
Enter a passphrase between characters. Enter a key renewal value to tell the Router how often it should change the encryption keys. The value must be between The default value is Enter the key shared between the Router and the server. It is a networking protocol that uses access servers to provide centralized management of access to large networks. Select either bits or bits from the drop-down list The bits encryption requires baandluxe hexadecimal digits.
The bits encryption requires 26 hexadecimal digits. This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other.
Enabling this option may provide your network with greater performance. The default is Open System authentication, where the sender and the recipient do not use a WEP key for authentication.