ASTM D4633 PDF

September 17, 2020   |   by admin

Designation: D − 10Standard Test Method for Energy Measurement for This test method is under the jurisdiction of ASTM Committee D18 on Soil and. Purchase your copy of ASTM D – 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available. ASTM D ,. “Standard. Test Method for Stress Wave. Energy Measurement for Dynamic. Penetrometer. Testing. Systems”. [2], speclfles.

Author: Samurg Mekasa
Country: Romania
Language: English (Spanish)
Genre: Career
Published (Last): 23 August 2011
Pages: 23
PDF File Size: 1.55 Mb
ePub File Size: 16.42 Mb
ISBN: 146-1-54317-243-2
Downloads: 60982
Price: Free* [*Free Regsitration Required]
Uploader: Fenrilkis

What is a standard?

Standard Test Method for Energy Measurement for Dynamic Penetrometers

The procedures used do c4633 consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. When you use our service you can be assured the latest editions and easy access. Link to Active This link will always route to the current Active version of the standard.

This astj may also be applicable to other dynamic penetrometer tests. Alternatively, the N-value can be used directly in foundation design using correlations to design parameters such as allowable bearing pressure or pile capacity. Valid Buy this standard.

Subscribe on standards – Read more. In addition, they are representative of the significant digits that generally should be retained.

Message to your colleague. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. This procedure may also be applicable to other dynamic penetrometer tests. Practice D provides a means of evaluating some of those factors.

  LAKO JE SMRSATI PDF

In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. This energy measurement procedure can evaluate variations of N-value resulting from differences in the hammer system.

The N-value depends on the soil properties but also on the mass, geometry, stroke, anvil, and operating efficiency of the hammer. Report error on page. The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard.

Users of this standard are cautioned that compliance with Practice D does not in itself assure reliable results.

ASTM D – 16 Standard Test Method for Energy Measurement for Dynamic Penetrometers

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Engineering properties can be estimated on the basis of empirical correlations between N-values and soil density, strength or stiffness. Shopping cart Close cart 0, foreach: Sustainable Development Goals and standardisation, how do they connect?

ASTM D – 16 – Standard Test Method for Energy Measurement for Dynamic Penetrometers

Contact us svenska Login. Read more about SIS Subscriptions. See also C4633 1- 6. Reliable results depend on many factors: Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. The Standard Penetration Test asgm the most common type. Soil and Rock I: It is not intended for use with down-hole hammers.

  EL VIAJE FANTASTICO KALIMAN PDF

Since the measured energy includes the extra potential energy effect due to the set d4633 blow, tests for energy evaluation of the hammer systems should be limited to moderate N-value ranges between 10 and 50 Ref 7. It is not intended for use with down-hole hammers. Your shopping cart is empty. The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

These notes and footnotes excluding those in tables and figures shall not be considered as requirements asym the standard. Subscribe on standards with our subscription service. Historical Version s – view previous versions of standard.

qstm The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used.

General terms and conditions Cookies och Javascript Disclaimer Contact. Please note that the selected standard is invalid. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. The standard is now in your shopping cart.