APS997C INSTALLATION MANUAL PDF

May 13, 2020   |   by admin

Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.

Author: Akinogul Vudozragore
Country: Vietnam
Language: English (Spanish)
Genre: Software
Published (Last): 8 November 2016
Pages: 205
PDF File Size: 18.95 Mb
ePub File Size: 11.87 Mb
ISBN: 703-4-51700-478-4
Downloads: 65258
Price: Free* [*Free Regsitration Required]
Uploader: Feramar

Parking Light Flasher Input This wire is the common contact of the on board parking light flasher relay. Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire.

Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting.

PLATINUM APSC INSTALLATION MANUAL Pdf Download.

To connect to the key in sensor circuit as shown for method 2: Connect this wire to the vehicle’s installatin light feed wire. To achieve optimum performance the coil signals must be evenly distributed. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.

You can enter Bank 3 from Bank aps997d by turning the ignition key off then on after you’ve made the changes you wanted in Bank 2, Siren two Long ChirpYou can also go insstallation to bank 3 by: The following two circuits may be used only if the above circuit is not available.

  DISCRETE MATHEMATICS WITH APPLICATION BY SUSANNA S.EPP PDF

Locate the control wire that connects the drivers door pin switch to the key in sensor switch. Tachometer Input Signal This wire will continually monitor the engine’s tach rate while the unit is under power of the Remote Start module.

Don’t have an account? Draw a circle around any of the columns. After you have inshallation the operation of the Audiovox Remote Start unit and tested all the safety features of the system: For technical support go to www. Enter text from picture: The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above aps9997c level it was before the vehicle began to crank which indicates the vehicle is running.

Manual Override Safety Testing and Operation.

Platinum APS-997C Installation Manual

Page 18 Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules.

Parking Light Flasher Feed This wire is the common contact of ap997c on board parking light flasher relay. When selecting Diesel operation, Bank 3 Feature 11over gasoline, the only change is to the ignition circuits.

Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear. Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle.

  EXAMEN PSYCOWIN PDF

Comments to this Manuals Your Name.

Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method. Page of 28 Go. Page 27 b 27 of If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger.

Programming Remote Start Feature Bank 3. Monitoring The Vehicle’s Engine: Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay. If the vehicle’s parking lights are ground switched, connect this wire to chassis ground. Enter text from picture: Page 10 12 White Wire: Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle.

Got it, continue to print. Multi Coil Adaptor Optional Information. In most cases, the Purple wire will need to be connected to only one door switch no matter how many doors the vehicle has as manuaal door lighting circuits are wired in parallel. Page 25 To decrease sensitivity, turn the adjustment screw counter clockwise.

Choose a location above the belt line dashboard of the vehicle for best reception.