AIRTRONICS VG6000 MANUAL PDF

September 28, 2020   |   by admin

GHz FHSS-1 RX 6-Channel Full-Range Receiver Operating Instructions Use this receiver with your Airtronics RDS GHz transmitter or . We appreciate your purchase of this new AIRTRONICS. VG or VG Radio System. These instructions are intended to acquaint you with the many unique. Airtronics/Sanwa VG Modes? Radios. All; Planes; Sailplanes; Helis; FPV; Multirotors; Cars; Boats. About Sanwa VG Here you can.

Author: Vulkis Faushakar
Country: Burundi
Language: English (Spanish)
Genre: Love
Published (Last): 25 June 2008
Pages: 107
PDF File Size: 11.47 Mb
ePub File Size: 4.68 Mb
ISBN: 949-9-89662-640-2
Downloads: 34920
Price: Free* [*Free Regsitration Required]
Uploader: Grogami

Cho, Ikoma-City, Nara, Japan.

After use, to prevent any chance of damaging the antenna, the antenna should be moved into the airtrlnics stowed position. The transmitter is now in Low Power Mode. It is extremely important to install the receiver and route the receiver antenna wires correctly vg60000 your model.

We further certify that the necessary measurements were. The VG is packed with all of the capabilities that the beginner as well as the more advanced modelers demand. The Bind LED on the receiver will blink slowly. Your battery is rated at 9.

Airtronics VG Manuals

Programmable Fail Safe is available on channels 1 through 4 only. Once the binding process is complete, the setting is remembered even when the transmitter and receiver are mnaual OFF, therefore, this procedure usually only needs to be done once for each separate receiver you’re using. The Trainer system in the VG transmitter allows you to connect any two Airtronics RD series transmitters together for the purpose of training a new pilot. To adjust stick length, hold Part B with your fingers and unscrew Part A counterclockwise to loosen the two pieces.

If you have little to no experience operating models, we strongly recommend you seek the assistance of experienced modelers or your local hobby shop for guidance. The receiver should be mounted securely in your model and the receiver antenna wires installed per the diagram below.

We artronics that you charge the transmitter battery while installed with the supplied ATX charger, Part Z. To the best of our knowledge, these tests were performed using measurement procedures consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standards.

  LINKSYS WAG200G INSTRUKCJA PDF

Airtronics VG Transmitter/Receiver/Switch Harness – RC Groups

manuall Aircraft fuselages and helicopter frames may contain conductive components. For example, the Fail Safe can be set so that the throttle servo returns to low, the elevator moves slightly up, and the ailerons move slightly right or left, to result in gg6000 shallow decent. In addition, the receiver should be wrapped in foam rubber to protect it from vibration. To set you throttle cut first you must make sure the throttle is working properly and it will come to a low idle.

If there is a problem with servo movement, try moving to a different position while still maintaining the same distance from your model, then check servo movement again. By moving the Dual Rate Elevator switch you can see the 1 and 2 turn off and on in conjunction aiirtronics the switch location 1 or 2.

Check to make sure that all receiver, servos, switch, and onboard battery connections are correct and secure.

The coaxial cables the thicker portion of the receiver antenna wires can be bent into gentle curves, however, do not bend the coaxial cables acutely, or repeatedly bend them, or the antenna cores can be damaged.

The Bind LED on the transmitter will illuminate solid blue. The Bind LED on the receiver will continue to blink slowly. On a fully charge battery, you may see the voltage as high as Do not cut or extend the receiver antenna wires. In this case, turn both the transmitter and receiver OFF, then repeat the binding procedure.

All your setting are saved in a eprom chip that does not need any type of battery to aitrronics its memory. Unlike ordinary crystal-based systems, your model can be used without frequency control.

The receiver should be wrapped in foam and the foam should be secured around the receiver to hold it in place. If mounting the receiver surrounded by conductive materials for example, a carbon fiber fuselagemount the receiver so that the antenna airtronice wires can be extended outside of the model.

  CLASSIFIED WOMAN THE SIBEL EDMONDS STORY PDF

Airtronics VG6000 (6 channel computer radio)

Got it, continue to print. Once the frequencies have been cleared, or the saturation level has dropped, your radio control system should be able to bind without any problems. If the throttle stick is not in the low position, when you turn it on, you will hear a continuous beeping sound and the display will read HI.

Do not attempt to fly with the transmitter in Low Power Mode. Don’t have an account? This operation is referred to as ‘binding’. Don’t show me this message again.

AIRTRONICS VG6000 Manuals

The throttle cut feature will do just that. It can be dangerous if you activate the airtromics in reverse order as the servos may start up inadvertently. Also, conduct a range test at the area of operation to ensure that the radio control system has complete control of the model at the farthest reaches of the operational area. Add to my manuals Add. You should set the packaging aside for use if you ever need to send your radio in for service, or to store your radio in case you do not plan to use it for an extended period of time.

When the binding procedure is successful, the Bind LED on the receiver will stay solid blue when both the transmitter and receiver are turned ON. Failure to mount the receiver antenna wires as described can result in poor reception, gg6000 in some cases, complete loss of reception. Due to differences in the implementation of 2.